# Converting numbers

### From HaskellWiki

BrettGiles (Talk | contribs) m (heading guidelines, formatting) |
(link to Generic number type) |
||

Line 20: | Line 20: | ||

=== Rational to Integral === |
=== Rational to Integral === |
||

− | this is inherently a lossy transformation since integral types cannot express non-whole numbers. depending on how you wish to convert, you might choose one of several methods. |
+ | Ihis is inherently a lossy transformation since integral types cannot express non-whole numbers. |

+ | Depending on how you wish to convert, you might choose one of several methods. |
||

* <hask>ceiling</hask> |
* <hask>ceiling</hask> |
||

Line 29: | Line 29: | ||

== original == |
== original == |
||

− | hi i am trying to write some funs that convert between two coordinate systems. the first coordinate system, which ill call coord1, starts in the upper left at (0, 0) and ends in the lower right at (500, 500). coords in coord1 have type (Int, Int). the second coord system, which ill call coord2, starts in the lower left at (0.0, 0.0) and ends in the upper right at (1.0, 1.0). coords in coord2 have type (Float, Float). i was hoping someone could help me figure out how i can rewrite the two funs below so that the type checker will accept them. |
+ | Hi, I am trying to write some funs that convert between two coordinate systems. The first coordinate system, which ill call coord1, starts in the upper left at (0, 0) and ends in the lower right at (500, 500). Coordinates in coord1 have type (Int, Int). The second coord system, which ill call coord2, starts in the lower left at (0.0, 0.0) and ends in the upper right at (1.0, 1.0). Coords in coord2 have type (Float, Float). I was hoping someone could help me figure out how I can rewrite the two functions below so that the type checker will accept them. |

<haskell> |
<haskell> |
||

coord1ToCoord2 :: (Int, Int) -> (Float, Float) |
coord1ToCoord2 :: (Int, Int) -> (Float, Float) |
||

Line 49: | Line 49: | ||

coord2ToCoord1 (1.0, 1.0) -> (500, 0) |
coord2ToCoord1 (1.0, 1.0) -> (500, 0) |
||

</haskell> |
</haskell> |
||

− | ah. i realize what is messing me up. |
+ | Ah. I realize what is messing me up. |

− | when i saw an expression like |
+ | When i saw an expression like |

<haskell> |
<haskell> |
||

500 * 0.2 |
500 * 0.2 |
||

Line 64: | Line 64: | ||

</haskell> |
</haskell> |
||

now that i have a better understanding i am able to write my funs. thank you for your help :) |
now that i have a better understanding i am able to write my funs. thank you for your help :) |
||

+ | |||

+ | == Automatic conversion == |
||

+ | |||

+ | Repeatedly people ask for automatic conversion between numbers. |
||

+ | Refer to the thoughts about a [[Generic number type]]. |
||

+ | |||

[[Category:Mathematics]] |
[[Category:Mathematics]] |

## Revision as of 12:24, 20 June 2007

Converting between numerical types in haskell must be done explicitly, this is unlike languages like C which automatically cast between numerical types in certain situations.

## Contents |

## 1 Integral types

Integral types are ones which may only contain whole numbers and not fractions such as## 2 Rational types

- toRational
- fromRational

## 3 Going back and forth

### 3.1 Integral type to rational type

- toRational

### 3.2 Rational to Integral

Ihis is inherently a lossy transformation since integral types cannot express non-whole numbers. Depending on how you wish to convert, you might choose one of several methods.

- ceiling
- floor
- truncate
- round

## 4 original

Hi, I am trying to write some funs that convert between two coordinate systems. The first coordinate system, which ill call coord1, starts in the upper left at (0, 0) and ends in the lower right at (500, 500). Coordinates in coord1 have type (Int, Int). The second coord system, which ill call coord2, starts in the lower left at (0.0, 0.0) and ends in the upper right at (1.0, 1.0). Coords in coord2 have type (Float, Float). I was hoping someone could help me figure out how I can rewrite the two functions below so that the type checker will accept them.

coord1ToCoord2 :: (Int, Int) -> (Float, Float) coord1ToCoord2 (x, y) = (x/500, (500-y)/500) coord2ToCoord1 :: (Float, Float) -> (Int, Int) coord2ToCoord1 (x, y) = (500/(1/x), 500 - 500/(1/y))

examples of what i want. i think i have the logic right :)

coord1ToCoord2 (0, 0) -> (0.0, 1.0) coord1ToCoord2 (250, 250) -> (0.5, 0.5) coord1ToCoord2 (350, 350) -> (0.7, 0.3) coord1ToCoord2 (500, 500) -> (1.0, 0.0) coord2ToCoord1 (0.0, 0.0) -> (0, 500) coord2ToCoord1 (0.5, 0.5) -> (250, 250) coord2ToCoord1 (0.7, 0.7) -> (350, 150) coord2ToCoord1 (1.0, 1.0) -> (500, 0)

Ah. I realize what is messing me up.

When i saw an expression like

500 * 0.2

i had assumed that 500 :: Integer because it didnt end in a .0. but it actually has type Double. so my problem was i would do something like this

(toInteger (500 :: Int)) * 0.2

which of course the typechecker wouldnt accept. now that i have rid myself of my incorrect assumptions i see that i should be writing

(fromRational (toRational (500 :: Int)) * 0.2) :: Float

now that i have a better understanding i am able to write my funs. thank you for your help :)

## 5 Automatic conversion

Repeatedly people ask for automatic conversion between numbers. Refer to the thoughts about a Generic number type.